Betekenis van:
characteristic curve

Voorbeeldzinnen

1. Reference characteristic wind speeds for angle βw=90° (vehicle in a curve with aq = 0,5 m/s2 and with aq = 1,0 m/s2).
2. Additional anti-pollution devices (if any, and if not covered by another heading)Description and/or (1) diagram(s):2.3. Fuel feed2.3.1. Feed pumpPressure (2) or characteristic diagram: kPa2.3.2. Injection system2.3.2.1. Pump2.3.2.1.1. Make(s):2.3.2.1.2. Type(s):2.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated)and r/min (maximum torque), respectively, or characteristic diagramState which method is used: on engine/on pump bench (1)2.3.2.1.4. Injection advance2.3.2.1.4.1. Injection advance curve (2):2.3.2.1.4.2. Timing (2):2.3.2.2. Injection piping2.3.2.2.1. Length: mm2.3.2.2.2. Internal diameter: mm2.3.2.3. Injector(s)2.3.2.3.1. Make(s):2.3.2.3.2. Type(s):2.3.2.3.3. Opening pressure (2) or characteristic diagram:2.3.2.4. Governor2.3.2.4.1. Make(s):2.3.2.4.2. Type(s):2.3.2.4.3. Speed at which cut-off starts under full load (2): r/min2.3.2.4.4. Maximum no-load speed (2): r/min2.3.2.4.5. Idling speed (2): r/min2.3.3. Cold-start system2.3.3.1. Make(s):2.3.3.2. Type(s):2.3.3.3. Description:
3. Lubricant temperature: minimum: K maximum: K4.1.16. Pressure charger: yes/no (1)4.1.16.1. Make:4.1.16.2. Type:4.1.16.3. Description of the system (e.g. maximum charge pressure, waste-gate, if applicable):4.1.16.4. Intercooler: yes/no (1)4.1.17. Intake system: maximum allowable intake depression at rated engine speed and at 100 % load: kPa4.1.18. Exhaust system: maximum permissible exhaust back pressure at rated engine speed and at 100 % load: kPa4.2. Additional anti-pollution devices (if any, and if not covered by another heading)Description and/or (1) diagram(s):4.3. Fuel feed4.3.1. Feed pumpPressure (2) or characteristic diagram: kPa4.3.2. Injection system4.3.2.1. Pump4.3.2.1.1. Make(s):4.3.2.1.2. Type(s):4.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated)and r/min (maximum torque) respectively, or characteristic diagramState which method used: on engine/on pump bench (1)4.3.2.1.4. Injection advance4.3.2.1.4.1. Injection advance curve (2):4.3.2.1.4.2. Timing (2):4.3.2.2. Injection piping4.3.2.2.1. Length: mm4.3.2.2.2. Internal diameter: mm4.3.2.3. Injector(s)4.3.2.3.1. Make(s):4.3.2.3.2. Type(s):4.3.2.3.3. Opening pressure (2) or characteristic diagram (1):4.3.2.4. Governor(s)