Betekenis van:
intersection point

Voorbeeldzinnen

1. Observations shall be made at each intersection point falling on forested land.
2. ‘Target point’ means the intersection of the projection of the headform longitudinal axis with the front surface of the vehicle (see point A in Figure 6);
3. The value of brake pedal force ‘F’, at the point of intersection between this line and a horizontal line defined by a = aABS, is defined as FABS, extrapolated:
4. Twelve gold stars situated at equal intervals form an invisible circle whose centre is the point of intersection of the diagonals of the rectangle.
5. The direction of load application shall be maintained along a line passing by the above intersection to a point just above the thigh bar housing (see figure 2 of Appendix 1 to this Annex).
6. Such protection will be deemed satisfactory if the line of intersection of the outer edge of the margin plate with the bilge plating is not lower at any part than a horizontal plane passing through the point of intersection with the frame line amidships of a transverse diagonal line inclined at 25 ° to the base line and cutting it at a point one half of the ship’s moulded breadth from the middle line.
7. Apply a 100 ± 10 N load to the back and seat pan assembly of the 3-D H machine at the intersection of the hip angle quadrant and the T-bar housing. The direction of load application shall be maintained along a line passing by the above intersection to a point just above the thigh bar housing (see figure 2 of Appendix 1 to this Annex).
8. Apply a 100 ± 10 N load to the back and pan assembly of the 3-D H machine at the intersection of the hip angle quadrant and the T-bar housing. The direction of load application shall be maintained along a line passing by the above intersection to a point just above the thigh bar housing (see figure 2 of Appendix 1 to this Annex). Then carefully return the back pan to the seat-back.
9. Apply a 100 + 10 N load to the back and pan assembly of the 3-D H machine at the intersection of the hip angle quadrant and the T-bar housing. The direction of load application shall be maintained along a line passing by the above intersection to a point just above the thigh bar housing (see figure 2 of appendix 1 to this annex).
10. In the case of a headlamp designed to provide a driving beam and a passing beam, measurements of the illumination produced on the screen by the driving beam shall be taken with the same headlamp alignment as for measurements under paragraphs 6.2.5 to 6.2.7 above; in the case of a headlamp providing a driving beam only, it shall be so adjusted that the area of maximum illumination is centred on the point of intersection of lines hh and vv; such a headlamp need meet only the requirements referred to in paragraph 6.3.
11. Rig for testing anti-roll properties on 1/1,5 gradient Figure 6.5 Data required for calculating the overturn of a tractor with triaxial rolling behaviour Note: D2 and D3 should be measured under full axle load. Figures 6.6.a, 6.6.b, 6.6.c Horizontal distance between the centre of gravity and the leading point of intersection of the protective structure (L6) Figure 6.7 Determination of points of impact for measurement of width of protective structure (B6) and height of engine bonnet (H7) axe 4
12. The south-east Atlantic (Major fishing area 47) comprises the waters bounded by a line beginning at a point at 6o04′36″ south latitude and 12o19′48″ east longitude; thence in a north-westerly direction along a rhumb line to a point at the intersection of the meridian 12o east with the parallel 6o south; thence due west along this parallel to the meridian 20o west; thence due south along this meridian to the parallel 50o south, thence due east along this parallel to the meridian 30o east; thence due north along this meridian to the coast of the African continent; thence in a westerly direction along this coast to the original point of departure.