Betekenis van:
pressure feed

Voorbeeldzinnen

1. Pressure in feed line for trailer braking system: … bar
2. Pressure in feed line for trailer braking system: … bar
3. The fuel feed pressure may be adjusted, if necessary, to reproduce the pressures existing in the particular engine application (particularly when a ‘fuel return’ system is used).
4. Productivity has consistently increased throughout the period under consideration from 115 tonnes in 2000 to 151 tonnes in 2003. This reflects the increasing use of automated feed systems and other labour saving devices, and the strong pressure to reduce costs in the face of mounting financial losses.
5. All portable containers for gases which are compressed, liquefied or broken down under pressure, which may feed a possible fire, shall immediately after use be put in a suitable place above the bulkhead deck, from which there is direct access to open deck.
6. Lubricant temperature: minimum: K maximum: K4.1.16. Pressure charger: yes/no (1)4.1.16.1. Make:4.1.16.2. Type:4.1.16.3. Description of the system (e.g. maximum charge pressure, waste-gate, if applicable):4.1.16.4. Intercooler: yes/no (1)4.1.17. Intake system: maximum allowable intake depression at rated engine speed and at 100 % load: kPa4.1.18. Exhaust system: maximum permissible exhaust back pressure at rated engine speed and at 100 % load: kPa4.2. Additional anti-pollution devices (if any, and if not covered by another heading)Description and/or (1) diagram(s):4.3. Fuel feed4.3.1. Feed pumpPressure (2) or characteristic diagram: kPa4.3.2. Injection system4.3.2.1. Pump4.3.2.1.1. Make(s):4.3.2.1.2. Type(s):4.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated)and r/min (maximum torque) respectively, or characteristic diagramState which method used: on engine/on pump bench (1)4.3.2.1.4. Injection advance4.3.2.1.4.1. Injection advance curve (2):4.3.2.1.4.2. Timing (2):4.3.2.2. Injection piping4.3.2.2.1. Length: mm4.3.2.2.2. Internal diameter: mm4.3.2.3. Injector(s)4.3.2.3.1. Make(s):4.3.2.3.2. Type(s):4.3.2.3.3. Opening pressure (2) or characteristic diagram (1):4.3.2.4. Governor(s)
7. Additional anti-pollution devices (if any, and if not covered by another heading)Description and/or (1) diagram(s):2.3. Fuel feed2.3.1. Feed pumpPressure (2) or characteristic diagram: kPa2.3.2. Injection system2.3.2.1. Pump2.3.2.1.1. Make(s):2.3.2.1.2. Type(s):2.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated)and r/min (maximum torque), respectively, or characteristic diagramState which method is used: on engine/on pump bench (1)2.3.2.1.4. Injection advance2.3.2.1.4.1. Injection advance curve (2):2.3.2.1.4.2. Timing (2):2.3.2.2. Injection piping2.3.2.2.1. Length: mm2.3.2.2.2. Internal diameter: mm2.3.2.3. Injector(s)2.3.2.3.1. Make(s):2.3.2.3.2. Type(s):2.3.2.3.3. Opening pressure (2) or characteristic diagram:2.3.2.4. Governor2.3.2.4.1. Make(s):2.3.2.4.2. Type(s):2.3.2.4.3. Speed at which cut-off starts under full load (2): r/min2.3.2.4.4. Maximum no-load speed (2): r/min2.3.2.4.5. Idling speed (2): r/min2.3.3. Cold-start system2.3.3.1. Make(s):2.3.3.2. Type(s):2.3.3.3. Description: