Betekenis van:
zero point

zero point
Zelfstandig naamwoord
    • the point on a scale from which positive or negative numerical quantities can be measured

    Synoniemen

    Hyperoniemen

    Werkwoord

    zero point

    Voorbeeldzinnen

    1. If the remote AFIS does not assign scores, then a score of zero should be used at the appropriate point.
    2. For processors not capable of performing calculations on floating point operands of 64-bit or more, the effective calculating rate R is zero.
    3. ‘The calibration curve must not differ by more than ± 2 % from the nominal value of each calibration point and by more than ± 0,3 % of full scale at zero.’;
    4. The beginning of the impact (zero point) at the moment of first contact of the body block with the steering control shall be identified on the recordings and films used for analysing the results of the test.
    5. The analyser shall not deviate from the nominal calibration point by more than ± 2 % of the reading over the whole measurement range except zero, or ± 0,3 % of full scale whichever is larger.
    6. if the zero values referred to in point (b) are no more than two, the calculation is made of the weighted average of the values referred to in point (a), as described in section 2.3, and the returned value is taken as the NRV;
    7. In order to calculate the exposure which arises on the non-trading book, institutions shall take the exposure arising from assets which are deducted from their own funds by virtue of point (d) of the second subparagraph of Article 13(2) to be zero.
    8. If it is obvious that procedural mistakes can be identified and/or considered highly likely, the specific data point is marked as an outlier and not included in subsequent statistical analysis. (A zero algal concentration in one out of two or three replicate vessels may indicate the vessel was not inoculated correctly, or was improperly cleaned).
    9. where a default value for greenhouse gas emission saving for the production pathway is laid down in part A or B of Annex V and where the el value for those biofuels or bioliquids calculated in accordance with point 7 of part C of Annex V is equal to or less than zero, by using that default value;
    10. exceeding that shown in line I but not exceeding that shown in line II when 25 % or more by volume distils at 300 °C by the ASTM D 86 method or, if less than 25 % by volume distils at 300 °C, when the pour point is higher than 10 °C below zero by the ASTM D 97 method.
    11. where a default value for greenhouse gas emission savings for the biofuel production pathway is laid down in Part A or B of Annex IV and where the el value for those biofuels calculated in accordance with point 7 of Part C of Annex IV is equal to or less than zero, by using that default value;
    12. As described in section I 9.1, points (4) and (7) of this Decision, the NPV approach used by Enova calculates the aid amount so that projects reach an NPV of zero, which, for a rational investor, would be the triggering off point for when a project is realized in the market.
    13. exceeding that shown in line I but not exceeding that shown in line II when 25 % or more by volume distils at 300 °C by the ASTM D 86 method or, if less than 25 % by volume distils at 300 °C, when the pour point is higher than 10 °C below zero by the ASTM D 97 method. These provisions apply only to oils having a diluted colour C of less than 2.
    14. The ‘equilibrium NPV’ scenario sets the NPV at zero, in other words the threshold of profitability of the operation; it corresponds to a cost of capital of 13,27 %, that is a beta of 1,56. In contrast, the ‘Ke — 2 %’ scenario corresponds to a 2 percentage point reduction in the cost of capital, due to the disappearance of the liquidity risk premium or a significant drop in the beta coefficient, or a combination of the two.
    15. (If a zero value is obtained, take the log10 value of the minimum detection limit of the analytical method used instead.)(ii) Calculate the arithmetic mean of the log10 values (μ).(iii) Calculate the standard deviation of the log10 values (σ).The upper 90‐percentile point of the data probability density function is derived from the following equation: upper 90‐percentile = antilog (μ + 1,282 σ).The upper 95‐percentile point of the data probability density function is derived from the following equation: upper 95‐percentile = antilog (μ + 1,65 σ).